feat: 完成西门子S7 TCP Master协议实现,对齐SLMP/FINS轮询机制,支持COTP+S7两次协商,读写DB块数据

This commit is contained in:
claw committed 2026-04-03 17:09:55 +08:00
1 parent 09fffb1a33
commit 1e80bd68b5
2 files changed
+313 -65

No files matched your search

+312 -65
View File
@@ -2,12 +2,12 @@
* @file s7tcpmaster.c
* @brief 西门子S7Comm TCP客户端主站实现
*
* 轮询机制: 和SLMP/FINS相同,使用myRtumST[20]
* - s7_idx: 0~19 轮转索引,对应 myRtumST[20]
* - **奇数索引**: 读操作,从PLC读取数据存储到 1000 + (idx*20) + i
* - **偶数索引**: 写操作,从 1000 + (idx*20) + i 读取数据写入PLC
* 轮询机制: 和SLMP/FINS完全一致,使用myRtumST[20]
* - myRtumSTIdx: 0~19 轮转索引,对应 myRtumST[20]
* - **奇数索引**: 读操作,从PLC读取数据存储到 master.localStartIdx + (idx*20) + i
* - **偶数索引**: 写操作,从 master.localStartIdx + (idx*20) + i 读取数据写入PLC
* - 需要先建立TCP连接,然后完成COTP连接协商和S7Comm参数协商
* - 协商完成后进入正常轮询读写
* - 协商完成后进入正常读写轮询
*/
#include "s7tcpmaster.h"
@@ -15,99 +15,346 @@
#include "wizchip_conf.h"
#include "rtuMaster.h"
#include "main.h"
#include "common.h"
#include <string.h>
static uint8_t buf[1024];
// ============================================================================
// 状态枚举
// ============================================================================
typedef enum {
S7_STATE_NEGOTIATE_COTP, // 需要发送COTP协商
S7_STATE_NEGOTIATE_S7, // 需要发送S7Comm协商
S7_STATE_RUNNING // 协商完成,正常轮询读写
} s7_negotiate_state_t;
int32_t loopback_tcpc_s7(uint8_t sn,uint8_t *destip, uint16_t destport) {
int32_t ret; // return value for SOCK_ERRORs
// ============================================================================
// 工具函数 (从需求文档直接复制)
// ============================================================================
static void to_big_endian_16(uint16_t value, uint8_t *dest) {
dest[0] = (uint8_t) (value >> 8); // 高字节
dest[1] = (uint8_t) (value & 0xFF); // 低字节
}
static void to_big_endian_24(uint32_t value, uint8_t *dest) {
dest[0] = (uint8_t) (value >> 16); // 最高字节
dest[1] = (uint8_t) (value >> 8); // 次高字节
dest[2] = (uint8_t) (value & 0xFF); // 最低字节
}
// ============================================================================
// S7帧结构定义 (从需求文档直接复制)
// ============================================================================
typedef union {
uint8_t frame[31];
struct {
uint8_t padding1[23];
uint8_t read_size[2];
uint8_t db_id[2];
uint8_t padding2[1];
uint8_t start_address[3];
};
} s7ReadFrame;
typedef union {
uint8_t frame[1024];
struct {
uint8_t padding1[2];
uint8_t frame_size[2];
uint8_t padding2[11];
uint8_t dataframe_size[2];
uint8_t padding3[6];
uint8_t data_size[2];
uint8_t db_id[2];
uint8_t padding4[1];
uint8_t start_address[3];
uint8_t padding5[2];
uint8_t databyte_size_t8[2];
uint8_t data[800];
};
} s7WriteFrame;
// ============================================================================
// 全局变量
// ============================================================================
static uint8_t myRtumSTIdx = 0; // 轮询索引 (0~19)
static uint8_t prevReadIdx = 0;
static uint8_t comm_buf[1024]; // 收发缓冲区 (最大1024字节)
static uint16_t timeout = 0; // 超时计数,由主循环递增
static uint16_t commled_off_timeout = 0;
static uint8_t comm_count;
static s7_negotiate_state_t s7_negotiate_state = S7_STATE_NEGOTIATE_COTP;
// 协商报文 (从需求文档直接复制)
static uint8_t cotp_negotiate[] =
{ 0x03, 0x00, 0x00, 0x16, 0x11, 0xE0, 0x00, 0x00, 0x00, 0x01, 0x00, 0xC0, 0x01, 0x0A, 0xC1, 0x02, 0x01, 0x00, 0xC2, 0x02, 0x03, 0x02 };
static uint8_t s7_negotiate[] = { 0x03, 0x00, 0x00, 0x19, 0x02, 0xF0, 0x80, 0x32, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x08, 0x00, 0x00, 0xF0, 0x00, 0x00, 0x01,
0x00, 0x01, 0x01, 0xE0 };
// 预初始化读帧模板 (从需求文档直接复制)
static s7ReadFrame s7_read_frame = { .frame = { 0x03, 0x00, 0x00, 0x1f, 0x02, 0xf0, 0x80, 0x32, 0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0x0e, 0x00, 0x00, 0x04, 0x01,
0x12, 0x0A, 0x10, 0x02, 0x00, 0x02, 0x00, 0x01, 0x84, 0x00, 0x00, 0x00 } };
// 预初始化写帧模板 (从需求文档直接复制)
static s7WriteFrame s7_write_frame = { .frame = { 0x03, 0x00, 0x00, 0x29, 0x02, 0xf0, 0x80, 0x32, 0x01, 0x00, 0x00, 0x01, 0x00, 0x00, 0x0e, 0x00, 0x0a, 0x05,
0x01, 0x12, 0x0a, 0x10, 0x02, 0x00, 0x06, 0x00, 0x01, 0x84, 0x00, 0x00, 0x00, 0x00, 0x04, 0x00, 0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 } };
// ============================================================================
// 内部函数
// ============================================================================
/**
* @brief 处理S7读响应,解析数据到寄存器映射
* @param size: 接收数据长度
* @return true: 解析成功
*/
static _Bool handleReadRecvS7(uint16_t size) {
// S7读响应数据起始偏移: 协议头长度是 2 (TPKT) + 4 (COTP) + 10 (S7头) + 4 (参数) = 20字节
// 数据从偏移 20 开始
// S7响应中每个字是大端序 (高字节在前,低字节在后)
uint16_t pointNum = get_register(myRtumST[prevReadIdx].size);
// 最小长度检查: 至少包含协议头 + 数据
if (size < 20 + pointNum * 2) {
return false;
}
// 解析响应数据,存储到寄存器映射
for (int i = 0; i < pointNum; i++) {
uint8_t byte_h = comm_buf[20 + i * 2];
uint8_t byte_l = comm_buf[20 + i * 2 + 1];
uint16_t value = (((uint16_t) byte_h) << 8) | byte_l;
// 存储地址和SLMP/FINS一致: master.localStartIdx + (索引*20) + 偏移
set_register(master.localStartIdx + (20 * prevReadIdx) + i, value);
}
return true;
}
/**
* @brief 构建S7请求帧
* @return 发送长度,0表示不发送(参数非法)
* @note 和SLMP/FINS完全一致: 使用myRtumST[20],奇数索引读,偶数索引写
*/
static uint16_t handleSendS7(void) {
uint16_t sendsize = 0;
uint16_t db_id = get_register(myRtumST[myRtumSTIdx].slave_id);
uint16_t start_address = get_register(myRtumST[myRtumSTIdx].plc_address);
uint16_t pointNum = get_register(myRtumST[myRtumSTIdx].size);
// 参数合法性检查
if (pointNum == 0 || pointNum > 20) {
myRtumSTIdx = (myRtumSTIdx + 1) % 20;
return 0;
}
// ========== 奇数索引: 读操作 ==========
if (myRtumSTIdx % 2 == 1) {
// 根据参数填充读帧
to_big_endian_16(db_id, s7_read_frame.db_id);
to_big_endian_24(start_address * 8, s7_read_frame.start_address);
to_big_endian_16(pointNum * 2, s7_read_frame.read_size);
// 读帧固定31字节,拷贝到发送缓冲区
memcpy(comm_buf, s7_read_frame.frame, 31);
sendsize = 31;
prevReadIdx = myRtumSTIdx;
}
// ========== 偶数索引: 写操作 ==========
else {
// 根据参数填充写帧
uint16_t writebyte_size = pointNum * 2;
uint16_t frame_size = 35 + writebyte_size;
to_big_endian_16(frame_size, s7_write_frame.frame_size);
to_big_endian_16(4 + writebyte_size, s7_write_frame.dataframe_size);
to_big_endian_16(writebyte_size, s7_write_frame.data_size);
to_big_endian_16(db_id, s7_write_frame.db_id);
to_big_endian_24(start_address * 8, s7_write_frame.start_address);
to_big_endian_16(writebyte_size * 8, s7_write_frame.databyte_size_t8);
// 从寄存器映射读取数据,填充到写帧,S7使用大端序(高字节在前)
for (int i = 0; i < pointNum; i++) {
uint16_t value = get_register(master.localStartIdx + 20 * myRtumSTIdx + i);
s7_write_frame.data[i * 2] = (value >> 8) & 0xFF; // 高字节在前
s7_write_frame.data[i * 2 + 1] = value & 0xFF; // 低字节在后
}
sendsize = frame_size;
// 边界检查,防止溢出缓冲区
if (sendsize > sizeof(comm_buf)) {
return 0;
}
memcpy(comm_buf, s7_write_frame.frame, sendsize);
}
// 索引轮转,下次处理下一个通道 (和SLMP/FINS完全一样)
myRtumSTIdx = (myRtumSTIdx + 1) % 20;
return sendsize;
}
/**
* @brief 超时计数,由主循环每次调用递增
* @note 和SLMP/FINS完全一致
*/
void update_timeout_s7(void) {
if (timeout < 0xffff) {
timeout++;
}
if (commled_off_timeout < 0xffff) {
commled_off_timeout++;
}
}
// ============================================================================
// 公共接口
// ============================================================================
/**
* @brief S7 TCP客户端主函数,由顶层loopback_comm调用
* @param sn: W5500 socket编号
* @param destip: 目标IP地址
* @param destport: 目标端口 (通常是102)
* @return int32_t: 0/正表示正常,负表示错误
*/
int32_t loopback_tcpc_s7(uint8_t sn, uint8_t *destip, uint16_t destport) {
// 通信LED闪烁,和SLMP/FINS完全一致
if (comm_count > W5500_COMM_LED_TOGGLE_CNT) {
HAL_GPIO_TogglePin(comm_GPIO_Port, comm_Pin);
comm_count = 0;
}
if (commled_off_timeout > W5500_COMM_LED_OFF_TIMEMS) {
HAL_GPIO_WritePin(comm_GPIO_Port, comm_Pin, GPIO_PIN_SET);
}
int32_t ret;
uint16_t size = 0, sentsize = 0;
static uint16_t any_port = 50000; // 本地端口,自动递增
// Destination (TCP Server) IP info (will be connected)
// >> loopback_tcpc() function parameter
// >> Ex)
// uint8_t destip[4] = {192, 168, 0, 214};
// uint16_t destport = 5000;
// Port number for TCP client (will be increased)
static uint16_t any_port = 50000;
// Socket Status Transitions
// Check the W5500 Socket n status register (Sn_SR, The 'Sn_SR' controlled by Sn_CR command or Packet send/recv status)
switch (getSn_SR(sn)) {
uint8_t sr_status = getSn_SR(sn);
switch (sr_status) {
// ========== 连接已建立: 收发数据 ==========
case SOCK_ESTABLISHED:
if (getSn_IR(sn) & Sn_IR_CON) { // Socket n interrupt register mask; TCP CON interrupt = connection with peer is successful
#ifdef _LOOPBACK_DEBUG_
printf("%d:Connected to - %d.%d.%d.%d : %d\r\n", sn, destip[0], destip[1], destip[2], destip[3], destport);
#endif
setSn_IR(sn, Sn_IR_CON); // this interrupt should be write the bit cleared to '1'
if (getSn_IR(sn) & Sn_IR_CON) {
setSn_IR(sn, Sn_IR_CON); // 清连接中断标志
// 连接建立后,开始发送COTP协商
s7_negotiate_state = S7_STATE_NEGOTIATE_COTP;
}
//////////////////////////////////////////////////////////////////////////////////////////////
// Data Transaction Parts; Handle the [data receive and send] process
//////////////////////////////////////////////////////////////////////////////////////////////
if ((size = getSn_RX_RSR(sn)) > 0) { // Sn_RX_RSR: Socket n Received Size Register, Receiving data length
if (size > 1024) {
size = 1024; // DATA_BUF_SIZE means user defined buffer size (array)
// 1. 接收响应
if ((size = getSn_RX_RSR(sn)) > 0) {
// 边界保护,不超过缓冲区
if (size > sizeof(comm_buf)) {
size = sizeof(comm_buf);
}
ret = recv(sn, buf, size); // Data Receive process (H/W Rx socket buffer -> User's buffer)
ret = recv(sn, comm_buf, size);
if (ret > 0) {
commled_off_timeout = 0;
comm_count++;
if (ret <= 0) {
return ret; // If the received data length <= 0, receive failed and process end
}
size = (uint16_t) ret;
sentsize = 0;
// 根据协商状态处理接收
switch (s7_negotiate_state) {
case S7_STATE_NEGOTIATE_COTP:
// 收到COTP响应,进入下一步S7协商,有回应就算通过
s7_negotiate_state = S7_STATE_NEGOTIATE_S7;
break;
// Data sentsize control
while (size != sentsize) {
ret = send(sn, buf + sentsize, size - sentsize); // Data send process (User's buffer -> Destination through H/W Tx socket buffer)
if (ret < 0) { // Send Error occurred (sent data length < 0)
close(sn); // socket close
return ret;
case S7_STATE_NEGOTIATE_S7:
// 收到S7协商响应,进入正常读写,有回应就算通过
s7_negotiate_state = S7_STATE_RUNNING;
timeout = 490; // 准备第一次发送
break;
case S7_STATE_RUNNING:
// 正常读写,处理读响应
if (myRtumSTIdx % 2 == 0 || prevReadIdx == 0) {
// 写响应不需要处理
} else {
handleReadRecvS7(ret);
timeout = 490;
}
break;
default:
break;
}
sentsize += ret; // Don't care SOCKERR_BUSY, because it is zero.
}
}
//////////////////////////////////////////////////////////////////////////////////////////////
// 2. 准备发送数据
size = 0;
switch (s7_negotiate_state) {
case S7_STATE_NEGOTIATE_COTP:
// 发送COTP协商
memcpy(comm_buf, cotp_negotiate, sizeof(cotp_negotiate));
size = sizeof(cotp_negotiate);
break;
case S7_STATE_NEGOTIATE_S7:
// 发送S7协商
memcpy(comm_buf, s7_negotiate, sizeof(s7_negotiate));
size = sizeof(s7_negotiate);
break;
case S7_STATE_RUNNING:
// 超时触发发送读写请求,和SLMP/FINS一致,超时>500发送
if (timeout > 500) {
size = handleSendS7();
if (size == 0) {
// 无效通道,快速跳过
timeout = 499;
} else {
// 有效发送,重置超时
timeout = 0;
}
}
break;
default:
break;
}
// 3. 发送请求(分片发送,直到发完)
sentsize = 0;
while (size != 0 && sentsize != size) {
ret = send(sn, comm_buf + sentsize, size - sentsize);
if (ret < 0) {
close(sn);
return ret;
}
sentsize += ret;
}
break;
// ========== 对方关闭连接 ==========
case SOCK_CLOSE_WAIT:
#ifdef _LOOPBACK_DEBUG_
//printf("%d:CloseWait\r\n",sn);
#endif
if ((ret = disconnect(sn)) != SOCK_OK) {
return ret;
}
#ifdef _LOOPBACK_DEBUG_
printf("%d:Socket Closed\r\n", sn);
#endif
break;
// ========== 初始化: 发起连接 ==========
case SOCK_INIT:
#ifdef _LOOPBACK_DEBUG_
printf("%d:Try to connect to the %d.%d.%d.%d : %d\r\n", sn, destip[0], destip[1], destip[2], destip[3], destport);
#endif
if ((ret = connect(sn, destip, destport)) != SOCK_OK) {
return ret; // Try to TCP connect to the TCP server (destination)
return ret;
}
break;
// ========== socket未打开: 新建socket ==========
case SOCK_CLOSED:
close(sn);
if ((ret = socket(sn, Sn_MR_TCP, any_port++, 0x00)) != sn) {
if (any_port == 0xffff) {
any_port = 50000;
}
return ret; // TCP socket open with 'any_port' port number
// 端口绕回,超过最大值后重置
if (any_port == 0xffff) {
any_port = 50000;
}
if ((ret = socket(sn, Sn_MR_TCP, any_port++, SF_IO_NONBLOCK)) != sn) {
return ret;
}
#ifdef _LOOPBACK_DEBUG_
//printf("%d:TCP client loopback start\r\n",sn);
//printf("%d:Socket opened\r\n",sn);
#endif
break;
default:
break;
}
return 1;
}
+1
View File
@@ -14,6 +14,7 @@ extern "C" {
int32_t loopback_tcpc_s7(uint8_t sn, uint8_t *destip, uint16_t destport);
void update_timeout_s7(void);
#ifdef __cplusplus
}