/* * @file finsudpmaster.c * @brief 欧姆龙FINS UDP客户端主站实现 * * 轮询机制: * - myRtumSTIdx: 0~19 轮转索引,对应 myRtumST[20] * - **奇数索引**: 读操作,从PLC读取数据存储到 + (idx*20) + i * - **偶数索引**: 写操作,从 + (idx*20) + i 读取数据写入PLC * - 每次主循环调用 update_timeout_fins() 递增超时计数 * - 超时计数 > 500 时发送下一帧,接收后重置超时为 490 */ #include "finsudpmaster.h" #include "socket.h" #include "wizchip_conf.h" #include "rtuMaster.h" #include "modbusSlave.h" #include "main.h" #include "common.h" #include static uint8_t comm_count; static uint8_t myRtumSTIdx = 0; // 轮询索引 (0~19) static uint8_t prevReadIdx = 0; static uint8_t comm_buf[1024]; // FINS收发缓冲区 (最大1024字节) static uint16_t timeout = 0; // 超时计数,由主循环递增 static uint16_t commled_off_timeout = 0; // 读响应固定头,只有匹配这个头才会被处理 // 格式: ICV(2) + RSV(2) + GATEWAY(1) + len(2) + cmd(1) + ... uint8_t readrx[14] = { 0xc0, 0x00, 0x02, 0x00, 0x0A, 0x00, 0x00, 0x01, 0x00, 0x00, 0x01, 0x01, 0x00, 0x40 }; // 预定义的请求模板 uint8_t send_read[18] = { // 读请求模板 0x80, 0x00, 0x02, 0x00, 0x01, 0x00, 0x00, 0x0a, 0x00, 0x00, 0x01, 0x01, 0x82, 0x00, 0x64, 0x00, 0x00, 0x0a }; uint8_t write_send[58] = { // 写请求模板 (最大20点 = 18 + 20*2 = 58字节) 0x80, 0x00, 0x02, 0x00, 0x01, 0x00, 0x00, 0x0b, 0x00, 0x00, 0x01, 0x02, 0x82, 0x00, 0x64, 0x00, 0x00, 0x02 }; // ============================================================================ // 公共接口 // ============================================================================ /** * @brief 处理接收到的FINS读响应 * @param size: 接收数据长度 * @param local_node: 本地节点号,填充到响应头比较 * @return true: 处理成功,false: 不是有效的读响应 * @note 只有读响应需要存储数据,写响应不需要处理 */ _Bool handleReadRecv(uint16_t size, uint16_t local_node) { // 1. 设置本地节点号,然后比对前14字节确认是读响应 readrx[4] = (uint8_t) local_node; for (int i = 0; i < 14; i++) { if (readrx[i] != comm_buf[i]) { return false; // 不匹配,不是读响应 } } uint16_t pointNum = get_register(myRtumST[prevReadIdx].size); // 5. 解析响应数据,存储到寄存器映射 // FINS使用大端序: 高字节在前,低字节在后 for (int i = 0; i < pointNum; i++) { uint8_t byte_h = comm_buf[i * 2 + 14]; uint8_t byte_l = comm_buf[i * 2 + 15]; uint16_t value = ((uint16_t) byte_h << 8) | byte_l; // 存储地址: + (索引*20) + 偏移 set_register(master.localStartIdx + (20 * prevReadIdx) + i, value); } return true; } /** * @brief 构建FINS请求帧 * @param local_node: 本地节点号 * @return 发送长度,0表示不发送(参数非法) * @note 奇数索引 -> 读操作,偶数索引 -> 写操作 */ uint16_t handleSend(uint16_t local_node) { uint16_t sendsize = 0; uint16_t slave_id = get_register(myRtumST[myRtumSTIdx].slave_id); uint16_t plc_address = get_register(myRtumST[myRtumSTIdx].plc_address); uint16_t pointNum = get_register(myRtumST[myRtumSTIdx].size); // ====================== // 无效 → 索引+1 → 下一个 // ====================== if (slave_id == 0 || slave_id >= 127 || pointNum == 0 || pointNum > 20) { myRtumSTIdx = (myRtumSTIdx + 1) % 20; return 0; } // ====================== // 奇数 = 读 // ====================== if (myRtumSTIdx % 2 == 1) { send_read[7] = (uint8_t) local_node; send_read[13] = (plc_address >> 8) & 0xFF; send_read[14] = plc_address & 0xFF; send_read[17] = (uint8_t) pointNum; sendsize = 18; memcpy(comm_buf, send_read, sendsize); prevReadIdx = myRtumSTIdx; } // ====================== // 偶数 = 写 // ====================== else { sendsize = 18 + pointNum * 2; write_send[7] = (uint8_t) local_node; write_send[13] = (plc_address >> 8) & 0xFF; write_send[14] = plc_address & 0xFF; write_send[17] = (uint8_t) pointNum; for (int i = 0; i < pointNum; i++) { uint16_t value = get_register(master.localStartIdx + 20 * myRtumSTIdx + i); write_send[18 + i * 2] = (value >> 8) & 0xFF; write_send[19 + i * 2] = value & 0xFF; } memcpy(comm_buf, write_send, sendsize); } // ====================== // 有效发送完成 → 下一个 // ====================== myRtumSTIdx = (myRtumSTIdx + 1) % 20; return sendsize; } /** * @brief 超时计数,由主循环每次调用递增 */ void update_timeout_fins(void) { if (timeout < 0xffff) { timeout++; } if (commled_off_timeout < 0xffff) { commled_off_timeout++; } } /** * @brief FINS UDP客户端主函数,W5500socket主循环处理 * @param sn: W5500 socket编号 * @param destip: 目标IP地址 * @param destport: 目标端口 * @param local_node: 本地节点号 * @return 0/正表示正常,负表示错误 */ int32_t loopback_udpc_omrfins(uint8_t sn, uint8_t *destip, uint16_t destport, uint16_t local_node) { if (comm_count > W5500_COMM_LED_TOGGLE_CNT) { HAL_GPIO_TogglePin(comm_GPIO_Port, comm_Pin); comm_count = 0; } if (commled_off_timeout > W5500_COMM_LED_OFF_TIMEMS) { HAL_GPIO_WritePin(comm_GPIO_Port, comm_Pin, GPIO_PIN_SET); } int32_t ret; uint16_t size = 0, sentsize = 0; static uint16_t any_port = 50000; switch (getSn_SR(sn)) { case SOCK_UDP: // 接收 if ((size = getSn_RX_RSR(sn)) > 0) { if (size > sizeof(comm_buf)) size = sizeof(comm_buf); ret = recvfrom(sn, comm_buf, size, destip, (uint16_t*) &destport); if (ret > 0) { commled_off_timeout = 0; comm_count++; handleReadRecv(ret, local_node); timeout = 490; } } // 超时触发发送 size = 0; if (timeout > 500) { size = handleSend(local_node); if (size == 0) { // 无效通道,快速跳过 timeout = 499; } else { // 有效发送,重置超时 timeout = 0; } } // 发送 sentsize = 0; while (size != 0 && sentsize < size) { ret = sendto(sn, comm_buf + sentsize, size - sentsize, destip, destport); if (ret < 0) break; sentsize += ret; } break; case SOCK_CLOSED: if (any_port == 0xFFFF) any_port = 50000; socket(sn, Sn_MR_UDP, any_port++, 0x00); break; default: break; } return 1; }